返回 聖衣大系 維修文章入口 整合
豺狼 維修記錄 2015-2017
Jackal Maintenance record 2015-2017
先繪製頭雕的顏色，先畫上眼白
First draw the color of the head sculpture, first draw the white of the eye
畫上眼線
Draw eyeliner
畫上眼珠
Draw eyeballs
畫上瞳孔
Draw pupils
畫上反光點
Draw reflective points
畫上眉毛
Draw eyebrows
畫上頭髮
Draw hair
完成後噴上透明漆，乾燥後再噴上消光漆
Spray clear paint after completion, then spray matte paint after drying
接下來開始整理鎧甲
Next, start finishing the armor
先處理塑膠零件
Handle plastic parts first
泡漂白水去除鍍層
Soak bleach water to remove the coating
去除鍍層完成
Finish removal of plating
拆解星座支架
Disassemble the constellation bracket
手甲的爪牙部分找出台版的原件準備克隆處理，港版原件大都損壞了
The minions of the hand armor found the original Taiwan version to prepare for cloning.
Most of the original Hong Kong version was damaged.
用圓棒將梢敲出來分離出爪牙
Use a round stick to knock out the tip to separate the minions
前方凹陷處用油土補起來
Fill up the depression in the front with oil and soil
開始埋油土製作模具
Started to bury oil soil to make molds
灌上矽膠
Filled with silicone
灌上石膏
Cast plaster
翻面去除油土
Turn over to remove oily soil
去除油土完成
Remove oily soil complete
塗上凡士林並加高積木
Apply petroleum jelly and raise the blocks
灌上矽膠
Filled with silicone
灌上石膏
Cast plaster
硬化後拆除積木
Remove the blocks after hardening
打開模具取出原件
Open the mold and take out the original
開始灌注克隆件
Start perfusion of clones
克隆的零件插上針
Plug the cloned part into the pin
再固定到框上
And then fixed to the frame
拍攝電鍍前置作業建檔
Preparatory work for shooting electroplating
塑膠原件插上針
Insert the pin on the plastic original
再固定到框上
And then fixed to the frame
拍攝電鍍前置作業建檔
Preparatory work for shooting electroplating
電鍍完成
Plating complete
整理好零件
Organize the parts
零件噴上第一層透明漆
The parts are sprayed with the first layer of clear paint
接著處理金屬件，這隻的金屬件不需電鍍處理只需要拋光
Then the metal parts are processed. This metal part does not need electroplating and only needs to be polished
拆下零件
Remove parts
浸泡溶劑去除漆層
Soak solvent to remove paint layer
零件用矽膠輪拋光，因為沒有要再一次電鍍，所以表面要拋的很亮
The parts are polished with a silicon rubber wheel, because there is no need to electroplate again, so the surface should be polished very bright
拋光效果對照
Polishing effect comparison
拋光完成
Polished
噴上透明漆防止氧化
Spray clear paint to prevent oxidation
準備修正塑膠件本身的色差
Prepare to correct the chromatic aberration of the plastic part itself
金屬件稍微偏藍色，所以塑膠件要噴上修正色
Metal parts are slightly bluish, so plastic parts should be sprayed with correction color
噴上修正色與原始對照
Spray the correction color with the original contrast
所有塑膠零件噴上修正的顏色
All plastic parts are sprayed with the correct color
這樣金屬與塑膠的基礎顏色就幾乎相同了
So the basic colors of metal and plastic are almost the same
開始塗遮蓋
Start applying mask
調主要的藍色 色彩成份為藍＋洋紅
The main blue color is blue + magenta
噴上藍色
Spray blue
塗上遮蓋再洗出銀色金屬
Apply the mask and wash out the silver metal
其他雙色零件繼續按照上述方式作業
Other two-color parts continue to work as described above
胸甲噴上淡藍色
Breastplate sprayed with light blue
噴上淺藍色
Spray light blue
去除遮蓋
Remove mask
牙齒週邊塗上遮蓋
Cover around the teeth
試組裝完成的零件
Trial assembled parts
塑膠件塗上遮蓋
Cover the plastic parts
用溶劑洗出銀色的牙齒
Wash out silver teeth with solvent
已完成的零件噴上透明漆
Finished parts are sprayed with clear paint
洗出眼睛的銀色鍍層
Wash out the silver coating of the eyes
洗出銀色鍍層
Wash out the silver coating
噴上藍色
Spray blue
面罩眼睛週邊塗上遮蓋並洗出銀色鍍層
Apply mask around the eyes and wash out the silver coating
噴上淡黃色
Spray light yellow
噴上淺藍色
Spray light blue
去除遮蓋
Remove mask
已完成的零件噴上透明漆
Finished parts are sprayed with clear paint
爪牙去除遮蓋
Minions remove cover
再次塗上不同區域的遮蓋
Apply a different area of coverage again
組裝星座支架
Assemble the constellation bracket
爪牙噴上調過色的黃色
Minions sprayed up the colored yellow
去除遮蓋
Remove mask
組裝星座型態
Assemble the constellation pattern
手甲的爪牙組合起來
Combine the minions of the hand armor
星座型態完成
Constellation pattern completed
人物型態缺了一個零件
Character is missing a part
自製的爪牙強度較差，多做幾個補件
Self-made claws have poor strength, so make a few more repairs
按照之前步驟上色
Follow the previous steps to color
寶石位置的周邊塗上遮蓋
Cover the periphery of the gem location
畫上寶石顏色乾燥後去除遮蓋
Paint the color of the gemstone and remove it after drying
面罩要做第二種型態，所以必須製作克隆件
The mask is to be the second type, so a clone must be made
將零件埋入油土
Buried parts in oily soil
圍上積木
Enclose the blocks
經過很多步驟後完成了模具
After many steps, the mold is completed
取出原件
Take out the original
開始灌注
Start perfusion
修整了一個與原始的對照
Trimmed a contrast with the original
一個是關閉的樣子 一個是打開的樣子
One is closed and the other is open
修改出需要的量
Modify the required amount
修改完成
Modification completed
將零件插上針
Insert the part into the needle
再固定到框上
And then fixed to the frame
拍攝電鍍前置作業
Preparatory work for shooting electroplating
電鍍完成
Plating complete
剪下需要的零件
Cut the required parts
插好零件準備上色
Insert parts ready for coloring
依照樣品噴上藍色
Spray blue according to the sample
再噴上透明漆就完成了
Then spray clear paint to finish
兩種型態的面罩
Two types of masks
人物型態零件終於到齊
Character parts are finally available
面罩蓋住的樣子
The way the mask is covered
面罩打開的樣子
The face mask opened
留言
張貼留言